Evo-Tec FAQ
-
What is the peak voltage output of an Evo-Tec On-Board Charger on the 24V Lithium setting?
Asked by Brandon M. in Ohio
ODIN
TECH GOD!Official AnswerOn the 24V Lithium setting, the Evo-Tec On-Board Charger’s peak voltage output is 28.40V.
Answered by Odin
TECH GOD!
-
What is the peak voltage output of an Evo-Tec On-Board Charger on the 16V Lithium setting?
Asked by Dylan B. in Wisconsin
ODIN
TECH GOD!Official AnswerOn the 16V Lithium setting, the Evo-Tec On-Board Charger’s peak voltage output is 17.75V
Answered by Odin
TECH GOD!
-
What is the peak voltage output of an Evo-Tec On-Board Charger on the 12V AGM setting?
Asked by Dominic R. in Illinois
ODIN
TECH GOD!Official AnswerOn the 12V AGM setting, the Evo-Tec On-Board Charger’s peak voltage output is 14.60V
Answered by Odin
TECH GOD!
-
What is the peak voltage output of an Evo-Tec On-Board Charger on the 12V Lead-Acid setting?
Asked by Chase M. in Missouri
ODIN
TECH GOD!Official AnswerOn the 12V Lead-Acid setting, the Evo-Tec On-Board Charger’s peak voltage output is 14.40V.
Answered by Odin
TECH GOD!
-
What is the peak voltage output of an Evo-Tec On-Board Charger on the 12V Lithium setting?
Asked by Blake H. in Arizona
ODIN
TECH GOD!Official AnswerOn the 12V Lithium setting, the Evo-Tec On-Board Charger’s peak voltage output is 14.20V.
Answered by Odin
TECH GOD!
-
Can I connect my Evo-Tec On-Board Charger to a generator to charge my batteries when off-grid?
Asked by Mason B. in Texas
ODIN
TECH GOD!Official AnswerYes, you can use a generator with your Evo-Tec On-Board Charger to charge your marine batteries off-grid. Make sure your generator has a high enough wattage available to power the charging banks of your Evo-Tec On-Board Charger.
Answered by Odin
TECH GOD!
-
How do I program my Norsk Lithium Evo-Tec On-Board Charger?
Asked by Marcus H. in Michigan
ODIN
TECH GOD!Official AnswerOnce the charger has been securely installed and before plugging the charger into an outlet, remove the fuse from the positive (+) lead from each bank on the charger.
After the fuse from the positive (+) lead from each bank on the charger has been removed, plug the charger into an outlet.
To program your charger, press the MODE button for each battery bank to select the proper charge output profile to match the chemistry and/or voltage of the battery to be charged. VERIFY all output profiles match the battery before use.
Once you have each bank of the charger programmed to the proper charge output profile to match the chemistry and/or voltage of EACH battery, connect the battery charger terminals from each battery bank to the appropriate battery to be charged based on chemistry and/or voltage. Once all connections have been made, reinstall the fuse(s) removed from the positive (+) lead from each bank on the charger.
NOTE: Your Norsk Lithium EVO-TEC charger will recall the charge output profile setting(s) selected during programming if the charger is disconnected from the wall outlet power the next time the charger is plugged into an outlet.
Answered by Odin
TECH GOD!
-
The mode button on my Evo-Tec On-Board Charger is not switching between 12V battery types.
Asked by Cole T. in Wisconsin
ODIN
TECH GOD!Official AnswerIf the mode button on your Evo-Tec On-Board Charger isn’t switching between battery types, you can try resetting the charger by following these steps:
1. Disconnect the charger from the outlet.
2. Remove the positive (+) fuse from your desired bank on your Evo-Tec charger.
3. Reconnect your Evo-Tec charger to the outlet.
4. Select your desired mode on your Evo-Tec charger using the mode button.
5. Reinsert the positive (+) fuse into the charger lead.
Answered by Odin
TECH GOD!
-
Can I extend the charging leads on my Evo-Tec On-Board Charger?
Asked by Jeffrey A. in West Virginia
ODIN
TECH GOD!Official AnswerWe suggest you avoid extending the charging leads of your Evo-Tec On-Board Charger if possible. Doing so may cause undesirable performance, excessive heat generation due to the increased resistance caused by the longer leads and may significantly shorten your charger’s lifespan.
If your install must have the charging leads extended, please be sure to review our wire gauge chart to ensure the correct gauge wire is used to prevent performance issues & excessive heat generation when charging. Using undersized wire could lead to damage and this would not be covered by the warranty.
Our wire size guide can be found here.
Answered by Odin
TECH GOD!
-
Can I connect my Evo-Tec On-Board Charger to the 28v terminals on my Norsk Lithium 36V 60AH battery?
Asked by Christopher L. in Georgia
ODIN
TECH GOD!Official AnswerNo, never connect your Evo-Tec On-Board Charger to the 28v terminals, only connect the charger to the 36V terminals.
Answered by Odin
TECH GOD!
-
Can my Evo-Tec On-Board Charger be used to charge other battery chemistries besides LiFePO4 lithium?
Asked by Bill D. in North Dakota
ODIN
TECH GOD!Official AnswerOn specific Evo-Tec On-Board Chargers, Bank 1 will have selectable battery chemistry modes: AGM, Lead Acid, and Lithium.
Answered by Odin
TECH GOD!
-
What are the dimensions of an Evo-Tec 3 Bank On-Board Charger?
Asked by Curtis N. in Colorado
ODIN
TECH GOD!Official AnswerThe size dimensions of the 3 Bank Evo-Tec On-Board Charger are 16.5 x 9.5 x 4 inches
Answered by Odin
TECH GOD!
-
What are the dimensions of an Evo-Tec 2 Bank On-Board Charger?
Asked by James H. in Florida
ODIN
TECH GOD!Official AnswerThe size dimensions of the 2 Bank Evo-Tec On-Board Charger are 11.5 x 9.5 x 4 inches
Answered by Odin
TECH GOD!
-
What are the dimensions of an Evo-Tec 1 Bank On-Board Charger?
Asked by Laura C. in New Mexico
ODIN
TECH GOD!Official AnswerThe size dimensions of the 1 Bank Evo-Tec On-Board Charger are 7.5 x 9.5 x 4 inches
Answered by Odin
TECH GOD!
-
Where can I find the product manual for my Evo-Tec On-Board Charger?
Asked by Benjamin P. in Alabama
ODIN
TECH GOD!Official AnswerYou can find the Evo-Tec On-Board Charger product manual here.
Answered by Odin
TECH GOD!